Paintless dent repair in Macungie, PA

Paintless dent repair tips? 1st let’s begin with some car paint care tricks: If you can not expose your car to the sunlight, you can use a hair dryer instead. Just aim the hair dryer to the areas you want to fix, and wait until the dents even out. The ideal distance between the hair dryer and the car should be 2-4 inches. While using a hair dryer, there should be an interval of 2 minutes. If the car’s paint starts discoloring, you should stop applying heat right away. Use a rubbing compound or wax to revise the paint color.

Hailstorm damage is a car owner’s worst nightmare and can easily be avoided with a few cautionary steps: try to park your car in a shaded or covered area, especially during seasons when hailstorms are prevalent. If you’re going to be going out of town for an extended amount of time, make sure that your car is parked in an enclosed area and, if possible, have someone check on it once in a while. Open spaces will leave your car helpless against the wrath of this natural phenomenon.

Use Hot Glue, Wooden Dowels, & Screws: When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun. Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.

I don’t care if you wash your car yourself (more on that strategy later in this page) or you take it to a quality car wash. (Yes, not all car washes are created equal) This is not an option as dirt is your #1 enemy when it comes to the finish on your new car paint. And this doesn’t mean once every 6 months whether it needs it or not. This means regularly and consistently. (A minimum of once a month…minimum!)

So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned. Read even more information on Auto Decals & Lettering Colorado Springs.

Using the Right Wax. Since each type of paint reacts differently to wax and polish, you need to find out which paint was used on your car and purchase detailing products that suit the paint. Some products may act as abrasive agents and strip the car off its original shine.

If you are considering learning the skill of how to do paintless dent repair, it’s important to understand that it isn’t simply a matter of “popping” a dent out and expecting that the body will be perfect again. PDR involves a very slow and methodical process that requires special tools, a certain level of knowledge and skill, and a great deal of patience. Some dent repairs, even on small dents, can take up to two hours.